Picture 1: What you see above is what you get. You get ONE (1)set of
Package comes with
-
RFID Access Controller with RS485 protocol networking function
-
RFID Card Reader . Click this icon to view the manual.
.
-
Cables
-
One RFID Card (click icon to buy more)
-
Electric door Bell Requires 2 pcs of AA batteries not included.
-
Electric door exit switch
-
Electric deadbolt with NC (Normally Closed) function and also live remote monitoring function.
-
One RFID Token (click icon to buy more)
PRODUCT DESCRIPTION
Offered here: new good quality RFID Access Controller & RFID Card that permits door access via password or RFID card or both. This console can work either as standalone or by connecting to a computer PC (Windows). You don't have to attach it to a computer in order to use it, set it up or program it. It can store 25,000 records when standalone, and the record will not disappear even when the unit is not powered for 10 years or more! It can support access control. You can set the door to open at different time and by certain number of people. It will raise an alarm when someone tries to destroy it or wrongly close/open the door that violates the pre-programmed instructions in the console. It supports RS485 and RS232 (via RS485/RS232 converter) communication interface to connect to a computer PC. The maximum number of this console that can connect to a computer terminal is 254 units. When connected to a computer terminal, the computer terminal with privileged password can remotely change the setting in any of the access controllers that is connected to it. It shares many similar functions as our fingerprint module (click on this icon: to learn more) except that it does not have fingerprint function and has RFID card function instead.
With your computer, you can manage user ids/RFID into major groups, each groups having different settings as to the time/date access privileges. After setting up, you don't need to connect the console to your computer to run it, since it can run independently of the computer.
The beauty of this console is that it can be connected to two pieces of waterproof external RFID mini card reader (included) at the same time via the Wiegand 26 port found at the back of the console. If you only connect one external card reader, you can put the external card reader on the outside of your door, and put this "RFPSRFY88CD" console on the inside of your door. If you attach two external waterproof RFID mini card reader, then the RFID function on the console will be turned off since the two external card reader will take over the RFID card reader job.
1) All-purpose and wide application. The product is integrated with PWD keyboard, single door controller, time recorder and double door controller.
2) Advanced technology, stable and reliable. All input and output pots can prevent shock from static and power. It has strong anti-interference ability and has power failure resisting design. The PCB board has moisture proof and corrosion protection and can adapt to different rough weather.
3) Dynamic definition, flexible application. One build-in card reader (EM or Mifare), two sets of W26 interface, two sets of sensor input, two sets of button input, two sets of relay output, one set of bell port and one set of RS485 communication interface. Re-define the IO interface. For example, W26 port will be defined as W26 standard output or input, the relay can be defined as door controller, bell or alarm output, the sensor can be defined as fire alarm signal.
Please note that the two set of relay input and output means that you can control two separate electric strikes/deadbolts/doors separately from one single controller. However, we do not advice buyer to do that because it may cause instability to the controller. This is especially true if the two separate electric strikes/deadbolts/doors are more than 30 meter apart. So if you must make full use of both relays, make sure the two separate electric strikes/deadbolts/doors are not too far apart.
4) Support hardware upload data on-line
5) Includes door close/open status monitoring function, so that you can monitor online whether your door is open or close. Will work with this electric strike that comes with monitoring function:
If you prefer one without networking function, then click on this icon:
If you prefer a wireless fingerprint access controller, then click on this icon and
KEY FEATURES:
Options to open door includes: 1. Password Only
2. RID Card Only (RFID token ( or ) you can register and deregister various RFID Card/passwords ( i.e. if you need to deactivate someone's access)
3. Password & RFID Card /token (click icons to purchase)
TECHNICAL SPECIFICATION Working voltage: AC/DC 8~25V Power consumption: <1W Data saving: >10 years (after power failure) Total user entry records: 25000 pieces (adjustable) User capacity: 2500 user id
LCD resolution: 122?32 DOTS Build-in word base: 16?16 national class two character base. Communication mode: One RS485 You need this optional RS485 to RS232 converter ( click on this icon if you want to buy) to link up a maximum of 255 pieces of RFID controller to one single PC. Relay output: Two State input: Four Card reading type: EM compatible or MIFARE Induction distance: 4 to 15cm Networking capacity: 254 sets Working temperature: -20celcius to +70 celcius Storage temperature: -25celcius to +85celcius
Working humidity: 20%-90% Wiegand 26 port: Two.
Dimension: 119mm*87mm*15mm
Also included in the package: new good quality RFID Access Controller.
This unit has the following advantages:
1. High performance.
2. Anti-interference capability / High stability
3. FTP support 26 bit Wiegand, permits maximum distance of 50m from card reader to this console (included)
4. Read RFID card (sold separately)
This unit must be connected to a console before it can function.
TECHNICAL SPECIFICATION Operating frequency: 125KHz
Adjustment Mode: ASK
Card: EM & RFID
Distance: 65mm
Respond Time: <0.1sec
Output format: 26bit Wiegand
Operating Voltage: DC5 to 16V
Current Draw: 20-50mA
Storage temperature: -25celcius to +85celcius
Working temperature: -20celcius to +70 celcius
Working humidity: 20%-90%
Dimension: 76mm*45mm*15mm
===============================================
The following is specifications for the electric deadbolt included in this listing:
Manual is included which is not shown in the photo above. Deadbolt comes with computer remote monitoring signal. When the strike is ready to use, you are able to remotely monitor the "close" or "open" status of your door from your desktop computer (assuming your access controller has networking function and is connected to a network). |
|
BRAND NEW door electric deadbolt / strike with NC (Normally Closed / Fail Safe) function. It also has a monitoring function. This function will send a signal to your access control unit (such as this or ) to inform the unit about the status of the deadbolt, whether it is in "close" or "open" position. Please note that your access control unit must have this monitoring function to be able to utilize this function. Our fingerprint module (click this icon or to buy it) does have this monitoring function.
Face plate: 205L x 35W x 40H (mm)
Strike: 90L x 25W x 2H (mm)
Cover Plate: 215L x 40W x 0.7H (mm)
Bolt: 16mm diameter, stainless steel 16mm throw
Material: Aluminum panel with strongly style and Stainless steel
Voltage: DC 12V
Current: Start 950mA / standby <=100mA (SUPER LOW HEAT!!!)
Patent Designed: Low temperature
Ideal for Wooden / glass / metal / fire proof door
Authority Certification: CE approved
Signal Output: Door status sensor
This item is rated: NC function -- Normally Closed -- Fail Safe (Locked when energized).
Safety function: Built-in voltage spike suppressor
Please note if you need a more advance version that will send monitoring signal to your access control unit as well as the ability to guarantee the bolt will come out / lock at the correct position (via a positioning ball) and not prematurely, then buy this deadbolt
(code:YHBOBSNC / click on this icon) :
Cable connection instruction:
1. Black cable: Connects the black cable to ground of your intelligent power supply.
2. Red cable: Connects the red able to NC terminal of your intelligent power supply.
3. White cables: connect one of the white cable to ground or "COM" port of your access controller such as or
Connect the other white cable to the signal port of your access controller. In the case of this controller, you connect to "SEN" port ("SEN" means sensor). In the case of this controller, you connect to "MC1" port on JP1 (Jumper 1) .
Hence, when the strike is ready to use, you are able to remotely monitor the "close" or "open" status of your door from your desktop computer (assuming your access controller has networking function and is connected to a network).
ATTENTION 1: Please note that this electric strike can connect directly to access control unit such as or listed below, but we do not suggest buyer to do so because it will shorten the lifespan of your access control unit due to high current passing through the electric strike. Instead, you should connect the strike directly to an intelligent uninterruptible power supply (UPS) that has NC/NO output. Make sure your UPS is "intelligent" meaning that it has NC or NO power output and can receive "door open" signal input from your access control.
ATTENTION 2: Normally Opened (NO) or Fail-secure rated electric strike remains locked during loss of power supply. Normally Closed (NC) or Fail-safe rated electric strike requires power to stay locked. When power is lost (such as a blackout), NC or fail-safe Electric Lock Strikes will remain unlocked until power is restored. Electric Strike that is NO rated may not be compliant with your local building / fire safety code. We personally feel that NC rated electric strike is safer. Buyer should check with their local safety code before making decision to buy a NC or NO rated electric strike. In order to ensure that power supply is not intentionally lost (in the event of theft/burglary), we suggest buyer to buy an Uninterruptible Power Supply shown below.
|